Number of commits found XX: 39

benchmarks/netperf: Fix build with clang 11 and gcc 10

Tested using poudriere on 11.3, 12.1, 13.0

PR:		249227
Reported by:	Krzysztof Galazka
Approved by:	build fix (blanket)
Sponsored by:	Intel

Add and use a shared INFO description. I have patches to add that knob to
a bunch of additional ports.

Drop the ipv6 virtual category for b* category as it is not relevant anymore

Turn installation of netperf.info into an option (default-on but allowing
to get rid of the texinfo dependency).

Install texinfo files (GNU info) into ${PREFIX}/share/info

After a discussion on the mailing list on moving manpages to
${PREFIX}/share/man for consistency with base where it is
installed in usr/share/man, it appeared the same should happen
to GNU info files which were installed under share in base and
not in ports.

Now texinfo is not in base on any of the supported version of FreeBSD
it is possible to proceed to this move and it is easier to do than
the manpage change.

Other benefit than consistency are less patching: all build tools but
cmake are expecting info files to be under share/info and cmake (patched here)
was having an exception for BSD so the patch makes FreeBSD case less
specific for them

Bump revision of all impacted ports

PR:		232907
exp-run by:	antoine
Differential Revision:	https://reviews.freebsd.org/D17816

Given that the netperf project hasn't rolled a release in quite some time,
switch to snapshots directly obtained from the github repository (currently
at version 2.7.1). Generally, there aren't that many changes since the 2.7.0
release version of netperf, the most noteworthy changes are in the area of
FreeBSD support, though:
- FreeBSD-specific code for letting netperf/netserver bind to CPUs, e. g.
  via the global "-T" option, has been added.
- The nettest_bsd back-end now can take advantage of aio(4) via the newly
  added test-specific "-a" and "-A" options, which in turn allows zero-copy
  send and receive with e. g. cxgbe(4). Note that this requires the netperf
  port to be built with its default-on OMNI option disabled, as otherwise
  the nettest_omni back-end and the migration to it from legacy back-ends
  (also the upstream default since netperf 2.5.0) will be used instead.

Apart from that, some test scripts missing in the published releases but
referenced by test scripts already part of e. g. netperf 2.7.0 are now
included.

Options are already optional.

Sponsored by:	Absolight

Remove dead links from MASTER_SITES or WWW

- Update to 2.7.0.
- Add an EXAMPLES knob.
- Unbreak CPU utilization measurement support for FreeBSD >= 10 [1], unbreak
  SCTP support for FreeBSD >= 10.

PR:	203752 [1]

Convert ports to use the options helpers in categories [abc]*, and minor fixes.

Sponsored by:	Absolight
Differential Revision:	https://reviews.freebsd.org/D3412?

Enable OMNI by default; this matches what vanilla netperf does since
version 2.5 and restores bidirectional compatibility with other OS
distributions following suit.

PR:		197137

- Fix check-plist by adding missing netperf.info file

Support stage

Add NO_STAGE all over the place in preparation for the staging support (cat:
benchmarks)

- Given that we always build netperf with --enable-demo, remove an
  irritating remark from the manual page suggesting it hasn't been.
- Grab

Approved by:	bapt (mentor)

- Fix build with clang [1]
- Use standard header
- Convert spaces to tabs in options and descriptions
- Spelling fixes in pkg-descr

PR:		ports/174887 [1]
Reported by:	Garrett Cooper <yanegomi@gmail.com> [1]

- Update to use OPTIONSNG
- Trim Makefile header
- Drop my maintainership

PR:		ports/173547
Submitted by:	edward
Feature safe:	yes

Upgrade to 2.6.0

1) Add OPTIONS support for:
- SOCKETS - Unix domain socket support and tests
- SCTP - Stream Control Transmission Protocol support and tests
- EXS - ICSC async socket support
- HISTOGRAM - Optional histogram output
- OMNI - Enable OMNI tests

2) Patch to $WRKSRC/configure which fixes CPU measurement and ROUTE
lookup routines in netperf, which result in this output:
-------------
checking which CPU utilization measurement type to use... "none.
Consider teaching configure about your platform."
checking which route lookup type to use... "none. Consider teaching
configure about your platform."
--------------

(Only the first 15 lines of the commit message are shown above )

Make UDP_STREAM work on IPv6 by transmitting and extracting IPv6
addresses correctly.  Otherwise bind(2) calls will fail, etc.

Submitted by: bz

Upgrade to 2.5.0.

Upgrade to 2.4.5.

Upgrade to 2.4.4.

Fix pkg-plist.

Fix plist.

Upgrade to 2.4.2.

Turn off -DHISTOGRAM as it introduces considerable overhead.  Bump portrevision.

Noticed by:     rwatson
Approved by:    sumikawa [MAINTAINER]

Upgrade to 2.3pl1.

Upgrade to 2.2pl4.

Make portlint(1) happy by changing strip to ${STRIP_CMD}

Submitted by:   Oleg Karachevtsev <ok@etrust.ru>
PR:             56998

Clear moonlight beckons.
Requiem mors pacem pkg-comment,
And be calm ports tree.

E Nomini Patri, E Fili, E Spiritu Sancti.

Upgrade to 2.2pl3.

Fix typo in patch-makefile.  IPv6 was not enabled.

Upgrade to 2.2pl2.  Almost of IPv6 patch was merged but netperf still
barks with -DDO_1644.

I'll take over this port.    

Upgrade to latest IPv6 patch. fix the error with -DDO1644.    

Add a MASTER_SITE_SUBDIR to unbreak fetching.   The checksum had also changed,
but it seems only the tarball was rerolled -   a comparison against an 'old'
archive from ftp.freebsd.org showed no   differences in content.    

Add checksum for IPv6 patch.  (Forgotten-by: kris)    

Add ipv6 to categories    

Number of commits found XX: 39

9 vulnerabilities affecting 70 ports have been reported in the past 14 days

^* - modified, not new

All vulnerabilities

Last updated:
2021-01-26 20:33:26