Sipcalc is an ip subnet calculator.
Features:
IPv4 -
* Retrieving of address information from interfaces.
* Classful and CIDR output.
* Multiple address and netmask formats (dotted quad, hex, number of bits).
* Output of broadcast address, network class, Cisco wildcard, hosts/range,
network range.
* Output of a userdefined number of extra networks.
* The ability to "split" a network based on a smaller netmask,
now also with recursive runs on the generated subnets.
* DNS resolution.
IPv6 -
* Compressed and expanded input addresses.
* Compressed and expanded output.
* Standard IPv6 network output.
* Reverse dns address generation.
* The ability to "split" a network based on a smaller netmask,
now also with recursive runs on the generated subnets.
* DNS resolution.
===> The following configuration options are available for sipcalc-1.1.6_1:
DOCS=on: Build and/or install documentation
===> Use 'make config' to modify these settings
Remove WWW entries moved into port Makefiles
Commit b7f05445c00f has added WWW entries to port Makefiles based on
WWW: lines in pkg-descr files.
This commit removes the WWW: lines of moved-over URLs from these
pkg-descr files.
Approved by: portmgr (tcberner)
Add WWW entries to port Makefiles
It has been common practice to have one or more URLs at the end of the
ports' pkg-descr files, one per line and prefixed with "WWW:". These
URLs should point at a project website or other relevant resources.
Access to these URLs required processing of the pkg-descr files, and
they have often become stale over time. If more than one such URL was
present in a pkg-descr file, only the first one was tarnsfered into
the port INDEX, but for many ports only the last line did contain the
port specific URL to further information.
There have been several proposals to make a project URL available as
a macro in the ports' Makefiles, over time.
(Only the first 15 lines of the commit message are shown above )
net-mgmt: remove 'Created by' lines
A big Thank You to the original contributors of these ports:
* @BABOLO <.@babolo.ru>
* Alex Samorukov, samm@freebsd.org
* Alexander Kriventsov <avk@vl.ru>
* Alexander Sulfrian <alexander@sulfrian.net>
* Alexander Y. Grigoryev <alexander.4mail@gmail.com>
* Alexandre Biancalana <ale@biancalanas.net>
* Alexandre Snarskii <snar@paranoia.ru>
* Alexandre Snarskii <snar@snar.spb.ru>
* Alexey Bobkov <mr.deadlystorm@gmail.com>
* Alexey Dokuchaev <danfe@FreeBSD.org>
* Alexey V. Degtyarev
(Only the first 15 lines of the commit message are shown above )
- Set --mandir and --infodir in CONFIGURE_ARGS if the configure script
supports them. This is determined by running ``configure --help'' in
do-configure target and set the shell variable _LATE_CONFIGURE_ARGS
which is then passed to CONFIGURE_ARGS.
- Remove --mandir and --infodir in ports' Makefile where applicable
Few ports use REINPLACE_CMD to achieve the same effect, remove them too.
- Correct some manual pages location from PREFIX/man to MANPREFIX/man
- Define INFO_PATH where necessary
- Document that .info files are installed in a subdirectory relative to
PREFIX/INFO_PATH and slightly change add-plist-info to use INFO_PATH and
subdirectory detection.
PR: ports/111470
Approved by: portmgr
Discussed with: stas (Mk/*), gerald (info related stuffs)
Tested by: pointyhat exp run
Say hello to the new "net-mgmt" category. There are probably more
ports that belong here than the ones I have identified and moved in
this, first, pass.
Approved in principle by: marcus
